Short answer: At most US trade shows booths are sold in 10-foot modules. A standard inline (linear) booth is 10×10 ft (3.05×3.05 m) or 10×20 ft, with an 8 ft (2.44 m) back wall allowed only in the rear half and a 4 ft (1.22 m) limit in the front half. Peninsula booths (three sides open, usually 20×20 ft or larger) and island booths (four sides open, typically 20×20 ft or larger) can go higher — 16 ft (4.88 m) is the typical maximum including signage. These are the IAEE (International Association of Exhibitions and Events) guidelines most US shows adopt; your own show’s rules always win.
Updated 25 October 2026. Figures quoted from the IAEE Booth Display Guidelines (© 2019) as reproduced in the AAP 2026 exhibitor rules. Shows can and do change them — always check the “booth display rules” in your exhibitor manual.
The booth types at a glance
| Booth type | Open sides | Typical size | Height rule (IAEE guideline) |
|---|---|---|---|
| Inline / linear | 1 | 10×10 ft (3.05×3.05 m); larger in 10 ft steps, e.g. 10×20 | 8 ft (2.44 m) back wall, only in the rear half; 4 ft (1.22 m) in the front half |
| Perimeter | 1 (backs onto the hall wall) | As inline | As inline, but back wall typically up to 12 ft (3.66 m) |
| End-cap | 3 | 10 ft deep × 20 ft wide (two booths) | 8 ft only in the rear half and within 5 ft (1.52 m) of the side aisles; 4 ft elsewhere |
| Peninsula | 3 | 20×20 ft or larger (at least four booths) | Typically up to 16 ft (4.88 m) in the centre of the back wall; 4 ft within 5 ft of each aisle where it backs onto inline booths |
| Split island | 3 (backs onto another peninsula) | As peninsula | As peninsula |
| Island | 4 | 20×20 ft or larger | Full cubic space usable up to the show’s maximum, typically 16 ft (4.88 m) including signage |
Inline booths (10×10 and 10×20)
The inline booth is the entry point for most exhibitors: one side on the aisle, neighbours left and right. The IAEE rule protects your neighbours’ sight lines — 8 ft is allowed only in the back half of the booth, and everything in the front half stays under 4 ft. When three or more inline booths are combined into one exhibit, the 4 ft limit applies only within 10 ft of an adjoining booth, which gives a 10×30 or larger inline exhibit more freedom in the middle.
Design consequence: on a 10×10 the back wall carries the brand, and counters, screens and product displays in the front half must stay low.
End-cap and peninsula booths
End-caps sit at the end of a row with aisles on three sides. Peninsulas are larger (usually 20×20 ft or more) and are the first size where real architecture — a tall central wall, a raised logo, a meeting room — becomes possible, because the typical maximum rises to 16 ft in the centre of the back wall. Where a peninsula backs onto inline booths, the 4 ft limit still applies within 5 ft of each aisle.
Island booths (20×20 and larger)
Island booths are open on all four sides and can use the full cubic space up to the show’s height limit — typically 16 ft including signage under the IAEE guideline, though some shows allow more (the AAP 2026 rules, for example, set 20 ft from the floor including lighting and truss) and some ask islands to keep part of each side see-through. Multi-storey booths and hanging signs are governed by each show’s own rules and usually need drawings approved in advance.
Feet to metres (for exhibitors coming from Europe and Türkiye)
| Feet | Metres |
|---|---|
| 4 ft | 1.22 m |
| 8 ft | 2.44 m |
| 10 ft | 3.05 m |
| 12 ft | 3.66 m |
| 16 ft | 4.88 m |
| 20 ft | 6.10 m |
| 10×10 ft booth | 9.3 m² |
| 20×20 ft island | 37.2 m² |
A 10×10 ft booth (9.3 m²) is close to a 3×3 m shell scheme stand in Europe, but the height rules are stricter: a European 2.5 m wall would be fine at the back of a US inline booth but too tall in its front half.
Before you design: four checks
- Find the booth display rules in your exhibitor manual and confirm your booth type, height limit and any see-through rule.
- Check whether hanging signs and multi-storey structures are allowed and what the drawing deadline is.
- If your builder is not the official contractor, register them as an EAC on time — see our guide to exhibitor-appointed contractors.
- Check the venue’s labor rules — our city guides cover Las Vegas, Chicago, Orlando, New York and Atlanta.
Getting a booth designed to your show’s rules
VAV Grup İnovasyon İnşaat Mimarlık Ltd. Şti. designs and builds custom trade show booths in its own production facility in İkitelli OSB, Istanbul and ships them to US shows, planning installation as your EAC where the show allows. Send your show name, booth number and size (for example “20×20 island”) through the form on this page or on WhatsApp and we reply with a concept drawn to that show’s height rules and an itemised quote. More on our USA trade show booth page.
FAQ
What is the most common trade show booth size in the US? The 10×10 ft inline booth, sold in 10 ft modules (10×20, 10×30). Larger exhibitors move to 20×20 ft peninsulas and islands.
How tall can a 10×10 booth be? Under the IAEE guideline, 8 ft (2.44 m) at the back wall, only in the rear half of the booth, and 4 ft (1.22 m) in the front half. Perimeter booths against the hall wall typically allow a 12 ft back wall.
How tall can an island booth be? Typically 16 ft (4.88 m) including signage under the IAEE guideline. Some shows allow more — check your manual.
What is the difference between a peninsula and an island booth? A peninsula is open on three sides and backs onto other booths; an island is open on all four sides. Both are usually 20×20 ft or larger.
Do these rules apply at every show? No. They are guidelines that many US shows adopt; the binding rules are the booth display rules in your show’s exhibitor manual.